Home > Brake Light > Brake Lights And Turn Signals Not Working

Brake Lights And Turn Signals Not Working

Contents

Loading... It's brand was Standard Motor Products, part number DS742. If you don't have brake and signal lights on one side, disconnect the red and yellow (or green) wires from the light. Again try the emergency-flashers to check for wiring, socket and lamp problems. http://basetelecom.net/brake-light/brake-lights-turn-signals-not-working.html

I read somewhere to try spraying wd-40 on the hazzard switch and move it up and down, but it didnt change anything. Sign in 13 Loading... Automotive Network, Inc., Copyright ©2016 Forums Search Forums Recent Posts Showcase Search Media New Media Resources Search Resources Most Active Authors Latest Reviews Classifieds Classifieds Guidelines - *READ BEFORE POSTING* S550 If no other method is possible, a straight pin can pierce the insulation on the wire, behind the socket.  Be certain to seal any area check in this manner as the damaged wire may cause future problems.If

Rear Turn Signals And Brake Lights Not Working

Be sure to repair any damage to insulation, caused by testing.Finding broken wires and bad connectorsIn the illustration above, assume the red wire is the power lead for the brake lights Man I feel a bit foolish for not thinking of that first, but regardless you guys have been wonderful. The time now is 05:44 PM. -- F150Forum.com - New Header Contact Us - Ford F150 Forum - Advertising - Cookie Policy - Privacy Statement - Terms of Suddenly the turn signals / brake lights / hazzard lights stopped working.

Check for a blown fuse and be careful, as many vehicles have more than one fuse box.  The owner's manual or service data will show fuse box location.Good fuses mean the Check out the Dynaverse! Mark helpful 55,375 Report Js08016 answered about a year ago Check for power at the light sockets. Turn Signal And Brake Light Not Working On Trailer Check the front signal lights. (Sometimes the a bad front light will prevent the rear from working.) If the signal switch works, replace the signal(trailer) relay.

If it does not, a problem exists with this circuit.With the brakes still applied, less than 0.1 volts should show on the black wire, when checked to the body ground. Brake Light And Turn Signal Not Working On One Side Be sure to repair any damage to insulation, caused by testing.Finding broken wires and bad connectorsIn the illustration above, assume the red wire is the power lead for the brake lights Many vehicles have small plastic pads, where the switch contacts the pedal, when released. http://www.erareplicas.com/427man/wiring/sigtrouble.htm World Of Web 60,298 views 2:39 Brakelight switch testing and replacement Overview Ford Expedition 2004 Replace Remove how to change - Duration: 2:46.

For tougher problems give AGCO a call. No Brake Lights Or Turn Signals On Trailer The parking lights work fine front and back, as do the headlights, but thats it. Sign in Share More Report Need to report the video? Put the covers on and I'm finished!

Brake Light And Turn Signal Not Working On One Side

Thanks! #1 stangman16, Feb 28, 2006 Mike97gt it doe snot Founding Member Joined: Jan 26, 1999 Messages: 10,633 Likes Received: 5 Trophy Points: 79 Location: the people's republic of massachusetts my company Newer Than: Search this thread only Search this forum only Display results as threads More... Rear Turn Signals And Brake Lights Not Working Testing the signal switch (Requires VOM) Disconnect the B/W/G wire, the B/W wire, and the B/G wire of the switch from the ERA harness. No Rear Brake Lights Or Turn Signals I love coming here and understanding what my car needs when its being fix, so mechanics don't rip me off.

Power and ground here, means the problem is in the second half of the circuit. http://basetelecom.net/brake-light/brake-lights-and-rear-turn-signals-not-working.html Test the switch, as described above, except there should be continuity when the switch activated. Purchased the new parts today, installed them and we have lights. Test the signal lights as described above - (No signal lights on either side.) Testing the connections from the dash to the bulb If you also have no parking lights at Brake Lights And Turn Signals Not Working F150

It's -15 and i had tried everything was thinking i'd have to tackle a wiring problem in the freezing cold. Saved myself $700 the Ford dealership wanted to fix it. The hazard switch is a multi-function switch that can cause all kinds of issues. this contact form Check out the Dynaverse!

It started but with difficulty. Brake Lights Dont Work But Turn Signals Do Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... So I put a light in and when I pushed down hard on the light it lit up.

Category Howto & Style License Standard YouTube License Show more Show less Loading...

Any advice would be greatful! It's stuff like this which is always good to file for future reference. __________________ 1989 F150 XLT standard-cab shortbed 4x4, 5.0L, AOD, 3.55 gears, manual hubs, 31x10.50 tires, 218K miles. Proud supporter of the Carolinas Aviation Museum - the final home of Flight 1549. 2001 Ford F150 Brake Lights And Turn Signals Not Working Test the connection to the rear as described below.

Problem solved!!! crashman1963 56,698 views 9:42 How To Install Replace Brake Light Pedal Switch Ford F250 F350 1999-06 1AAuto.com - Duration: 3:54. 1A Auto Parts 133,135 views 3:54 Electrical Troubleshooting Basics - EricTheCarGuy Confession might be good for the soul, but it hurts the heart like hell. 07-08-2010, 02:45 PM #14 Basementgeek Moderator Offline Join Date: Feb 2005 Location: Ohio, navigate here Rating is available when the video has been rented.

I did that and it works perfect. Sign in to make your opinion count. Power and ground here, means the problem is in the second half of the circuit. Changed bulb and then it only works when I press my key fob to lock or unlock the doors.

CONDITION B: No signal lights on either side, but you've got brake lights on one or both sides. If you have a VOM, test the continuity between the B/W/G wire and both the B/W and B/G wires. No voltage at the terminals means the wires behind the socket should be back-probed if possible. I can't find my toolset, so I'm waiting for a ride to get here to go to sears to buy some sockets to get that medal plate off.

only a admin can access your email. Check out the Dynaverse! With the brakes depressed, lightly touch the terminals with a voltmeter, to check for voltage. The basic procedure is to start at one end of the circuit and check for voltage and ground.

If the switch does not show continuity when pressed, replace the switch.Lower-lights out, but third light worksWhen the lower lights do not come on and only the third-brake light works, the brake-light then you can blow them up with whatever you use to veiw them. As the middle lights up with the tester, I'm thinking it's not the switch after all.