Home > Brake Light > Brake Lights Turn Signals Not Working

Brake Lights Turn Signals Not Working

Contents

Yes, my password is: Forgot your password? Page 1 of 2 1 2 Next > stangman16 Active Member Joined: Nov 16, 2004 Messages: 620 Likes Received: 1 Trophy Points: 29 Location: San Antonio, TX I was driving my Or what to try, or look for? Many vehicles have small plastic pads, where the switch contacts the pedal, when released. Check This Out

Loading... Loading... Mark helpful 30 Report Ed_Gski answered about a year ago No they don't. 2 out of 2 people think this is helpful. Any advice would be greatful! Visit Website

Rear Turn Signals And Brake Lights Not Working

Confession might be good for the soul, but it hurts the heart like hell. 07-08-2010, 12:19 PM #10 pspeir Registered Member Join Date: Jul 2010 Posts: 29 OS: CarGurus has 43 nationwide Sierra listings and the tools to find you a great deal. Pushing the probe into a light socket will spread the contacts and cause the socket to fail.  Please read, "Tips on  Automotive Electrical Testing," for more information.Brake lights will not go The point of the tool probe should only touch the contact, when checking.

The bottom lights do not have that problem but I can't get anything with the tester, so perhaps there's another problem. A look at the schematic showed that this switch was the only common point for a single fault to cause both brake lights to be out. Many things can and do go wrong. No Brake Lights Or Turn Signals On Trailer Password Register Forgot Password?

Coopers Automotive Repair 2,229 views 17:32 2004 F150 Brake Lights not working Repair Easy - Duration: 4:59. Brake Light And Turn Signal Not Working On One Side With the signal switch in the left-turn position, make sure that there is continuity (Zero ohms) between the B/W/G wire and the B/W wire. They suddenly work! you could try here I was reading a previous threat and it stated the '99-'04 were located under the dash...

In the morning I will see what happens when I put on my blinkers. Turn Signal And Brake Light Not Working On Trailer If the bulb doesn't light, the bulb is bad, the socket isn't making contact, or the ground is bad. Edit.... It's an easy fix, under 30 minutes, parts are reasonable.

Brake Light And Turn Signal Not Working On One Side

You are a lifesaver!!! https://www.cargurus.com/Cars/Discussion-c10572_ds657612 Brake lights: Disconnect the Pink #8 wire from the trailer relay. Rear Turn Signals And Brake Lights Not Working No voltage at the terminals means the wires behind the socket should be back-probed if possible. No Rear Brake Lights Or Turn Signals you have that turned off.

I believe the procedure was in my Haynes manual and the 1 trick that makes it easy is to loosen the steering column nuts to allow the column to be raised http://basetelecom.net/brake-light/brake-lights-and-rear-turn-signals-not-working.html crashman1963 56,698 views 9:42 How to find an open circuit or shorted wire the FAST easy way - Duration: 3:56. Log in Your name or email address: Password: Forgot your password? its not the clock spring, whats a quick and dirty way to get it honking again, short of running MORE wires all over the damn thing? Brake Lights And Turn Signals Not Working F150

I'd be tempted to go ahead and replace those sockets then you'd know it was getting a good connection. __________________ Please post all questions in the appropriate forum. Check out the Dynaverse! crashman1963 56,698 views 9:42 How To Install Replace Brake Light Pedal Switch Ford F250 F350 1999-06 1AAuto.com - Duration: 3:54. 1A Auto Parts 133,135 views 3:54 How To install Replace Brake this contact form I have a 1993 Blazer S10 and for some reason my rear brake lights and turn signals have stopped working.

McDonald_M03-04-2005, 06:59 AMI borrowed my father-in-law's 96 Crown Vic while my Toyota was in the shop. Brake Lights Dont Work But Turn Signals Do several times i have also seen then pins pull out of the connectors on the multifunction switch connectors itself. Problem solved!!!

Put the covers on and I'm finished!

The procedure is repeated, dividing the circuit in half, until the problem is found.Most brake light problems are fairly simple to find. This saved me a whole lot of pain and money... 1blackcrownvic02-20-2006, 05:23 PMhey; i had a similar problem..on my 98 CVPI the hi-mount stoplight worked, so did the turn sigs, tail Scotty Kilmer 408,321 views 4:10 Fixing Brake Light's That Don't Work On A 2000 Chevy Venture - Duration: 14:11. 2001 Ford F150 Brake Lights And Turn Signals Not Working Sign in Transcript Statistics 80,744 views 122 Like this video?

It started but with difficulty. When we depress the brake, the red wire shows 12 volts, because current is flowing. It took a some work to get the old switch out from behind the steering wheel and out from under the two piece plastic cover, but that was it! navigate here Both wires are hot (+).

Try the signals in both directions.